Elive

Everytime I reboot elive
Right / Left monitor and resolution are ok

But

I always have to reset who’s the primary screen

I do it, save, and the application bar goes on the right one but at reboot, the wrong screen as the application bar

Due in ver 2.0

please link prntscrn button to a prntscrn command

also please add

Shift+prntscrn for video recording

thank you

-David

When the printer is plugged, run the printer applet and when is unplugged, remove it

Hello.

I have to intent install the Elive 2.0 Topaz (elive_2.0_Topaz_new-kernel_up003.iso) in laptop IBM Thinkpad 380ED, but appear this message:
“Processor does not support: cmov”

Can you help me please ?

Best regards.

The systems reference sheet ­ ThinkPad 380ED

Processor Type: Pentium MMX 166/66 MHz / 64 bit transfer to L2 cache / 64 bit transfer to memory

Processor Upgrade: None

L2 cache: 256 KB / write­through / direct mapped / 8 ns / synchronous pipelined burst

Diskette Drive: Internal 3.5” 1.44 MB / use simultaneously with CD­ROM / on right side

External FDD port: None since diskette internal

CD­ROM: 5.25” CD­ROM / 8­20x speed / CAV / multi­session / XA / ATAPI / not bootable / not removable / on right side

Preload(see side): Windows 95 OSR2

Available date: September 1997

Disk ­ size / ms: 2.1 GB / 13 ms / PIO Mode 4 (2635­5AU), 3.0 GB / 13 ms / PIO Mode 4 (2635­6AU), 5.1 GB / 12 ms / PIO Mode 4 (2635­7AU)

Disk controller: EIDE / PCI 2.1 / supports one internal disk / no DMA or busmaster support / not removable / upgrade only by IBM or dealer

Display ­ size and type: 12.1 inch FRSTN color (2635­5AU), 12.1 inch TFT color (2635­6AU, 2635­7AU)

Display ­ technology: (2635­5AU) SVGA / 640 x 480 or 800 x 600
Dual scan / FRSTN / 150 ms / 70 nits 65,536 sim colors / 35 to 1 contrast
(2635­6AU, 2635­7AU)
SVGA / 640 x 480 or 800 x 600
Active Matrix TFT / 75 ms / 100 nits 65,536 simultaneous colors / 100 to 1 contrast ratio

Graphics ­ controller: NeoMagic MagicGraph128ZV (NM2093) /128 bit SVGA accelerator / Zoomed Video support / DDC1 and DDC2B 1.125 MB / DRAM (embedded) / color space conversion and interpolation in X and Y axis / support for DCI, DirectDraw

Graph ­ arch/data: PCI 2.1 / 32 bit / external SVGA to 1024 x 768 with 256 colors

Graphics ­ features: Simultaneous LCD and CRT / 150 degree tilt

Memory ­ std / max: 16 MB / 80 MB / non­parity / 3.3 volt / EDO

Memory ­ features: 1 socket for one JEDEC 144 pin EDO SO DIMM of 8, 16, 32, or 64 MB / socket accessed from bottom via screw

Keyboard / # of keys: Full size alp/num / 85 (6 Fn key functions) / keyboard slope with Port Replicator

External keyboard: External keyboard support with option cable 06G8619 or Port Replicator

Pointing/ palm rest: TrackPoint III / no drag lock keys

Battery ­ type / life: Li­Ion / non­intelligent / 2.0 hrs (2635­5AU), Li­Ion / non­intelligent / 2.5 hrs (2635­6AU, 2635­7AU)

Charge time ­ on/off: 4.2 to 12 hrs / 3.3 hrs

Architecture: PCI 2.1 / 32 bit / 33 Mhz (EIDE, graphics, PCMCIA, Port Replicator) ISA (audio, diskette, serial, parallel, infrared)
Intel Mobile Triton 82430 PCIset / Intel 82371MX PIIX / NS PC87338

PCMCIA slots: 2 Type I or 2 Type II or 1 Type III / Zoomed Video support in lower slot /PCMCIA 2.1 compatible / PC Card Standard 95 / Cirrus Logic CL­PD6729 (PCI)

Serial / parallel ports: One 9 pin; 16550A / one (IEEE P1284­A, EPP, ECP, bidirectional)

MPEG decoder: None (software support for MPEG­1 in Windows 95)

Audio support: 16 bit audio chip / 20 voice MIDI FM Synthesis / Crystal Semiconductor CS4236 One internal speaker / .5 watt / dial volume control / int mic / full duplex spk/mic

Audio in/out jacks: Input/microphone jack (stereo) / output jack (stereo) / no joystick port

Infrared ports Infrared port on left side / IrDA 1.1 compatible / up to 4 Mbps

Security: Power ­on password / Hard disk password / security keyhole / personalization

Preinstalled software: Microsoft Windows 95 OSR2 with applications (listed on right)

Elive 1.7.2 is unable to resume right after hibernating my PC.

# hibernate
Some modules failed to unload: nvidia
hibernate: Aborting suspend due to errors in ModulesUnloadBlacklist (use --force to override).

I have only one module from /etc/hibernate/blacklisted-modules - nvidia
version of nvidia driver is legacy-96xx

Resuming after “hibernate -f” finishes with black screen and num/caps locks’ leds, that doesn’t reacting on pressing nul/caps lock.
Usually, after spending some time with pressing ctrl-alt+del I’ve soft-reboot, but sometimes hard-reboot is the only chance to reboot.

/var/log/hibernate.log says, that it was unable to unload nvidia module and, that resuming was successfull

Hi, i have made a first installation, with the install code that i have received by mail. When i try to reinstall elive with my liveCD, the program tell my that the install code is not correct !
For my first install my code was “abd7b4367”. If i try to reinstall, i get a new code, for that my install code program received by mail don’t work anymore. What can i do ?
Thank for answering

Hi,
I use a line Alice ADSL Telecom Italia with the router “alice gate 2 plus wi-fi NMU 705000 by industrie dial face”, but the internet pages don’t appeare complete.
With Ubuntu 8.04 and WindowsXP is all ok, the problem exist with ELIVE STABLE and 1.77-1.7.10.
This problem happens only with the provider’s modem/router.

I tried to change the MTU on the ETH0 befor at 1500 and then 1492, but the problem remain.

NOTE: on the firmware Telecom Italia the value MTU cannot be changed (the router is too closed and it is not possible make changed except routing rules and the ability of IPTV).

Cuando voy a montar el hdd externo me dice fallo al montaje por formato ntfs, uso el hdd elements lo comparto en windows y en linux.

Write here a informational but simple description Sur Elive 1.8.8, Exalt ne fonctionne pas du tout, alors que sur la 1.8.4, il est parfaitement opérationnel.

Well every time you change the theme, the GTK switcher appears and the startup sound is quite annoying.
Version 1.9.54

Greetings:
Agust

when install the elive gem after confirm whit eliveuser and elive like password y see this in the panel: `
eliveuser@Elive[`]$_
after that nothing
what y due wrong ???

Wireless Network can’n use in LAPTOP DELL INSPIRON 1525.

use spanish please.

Hi

Just wondering if there is a way to get elive to access a wireless network using Protected EAP (PEAP) as WPA authentication.

I have installed FreeRadius from synaptic but don’t know how to configure it.

Repeated lines to Standard out for close error: [Errorno 10] No child processes. It seems similar in nature to this bug at http://mail.python.org/pipermail/python-bugs-list/2007-July/039036.html. Additionally the program that seems to be causing it is netconnectord.

Try it out, I get two terminals directly over top of each other. I think some people might not have an “Ins” or Insert key, does anyone have a different default key that they use to bring up a term (x2) window?

Hello, i don’t know if u have seen, but when u quit Elive, u have the screen with elive started, but elive quit, maybe a bug?

HP 6715b notebook

HP 6715b notebook with radeon X1250 integrated graphics - fglxr driver. Auto mode reports failure, but x loads fine. Setting monitor to 1600×1280 shows no error message and x loads fine

I have a couple old computers with Ati Rage 128 Pro 32MB cards. In both Revolution releases the detection of the video card dos not work properly and asks to choose fglrx, radeon or VESA drivers for X11, the first two failing, obviously, and the third one being terribbly slow.
The driver to use is r128, and changing that in /etc/X11/xorg.conf and restarting the X system everything works perfectly.

My Ralink RT2561 PCI wifi-card worked “out-of-the-box” with LinuxMint 4.0 and 5.0.
But even latest Elive dev 1.9.07 cannot handle it.
Drivers are available here:
http://www.ralinktech.com.tw/data/drivers/2008_0723_RT61_Linux_STA_v1.1.2.2.tar.bz2

Unfortunately I got no Idea how to deal with those files. Do I have to switch to LinuxMint for using it?

Crash with no reason

i have installed elive 1.9.18 on my laptop dell latitude d630.
and E17 crashed with no reason, for twice install.

i have wallpaper with blanck windows who write f1 resume or F4 quit, and when i put F1 i have entrance i relog, and same problem

El kernel actual no soporta o no trae el modulo raw 1394

mount ntfs filesystem with rw attributes in live mode, it forced re-check filesystem for win in the next boot.

I was very happy to see both qjackctl and zynaddsubfx as part of the default elive packages so I presumed it was also going to come with a real-time kernel as I heard that, as of 2.6.18, this has entered the mainline kernel code. Sadly this doesn’t seem to be the case.

This is the biggest missing feature in elive for me, and other wannabe Linux musicians too I’d think. If real-time support can’t be enabled it the primary elive kernel for whatever reason then it would be great if it came with a second, rt-enabled one too.

Missing drivers for Realtek 8191se PCI wireless card.

Tried downloading and installing from drivers on Realtek site but did not install properly it would seem.

Link to Realtek driver:
http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=48&PFid=48&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true